ERMANI bricket-80AT — Press for the production of concrete spacers for reinforcement

Description of the ERMANI hyperpress

ERMANI bricket
Hydraulic press, universal. For the production of concrete reinforcement spacers. This press can produce many types of spacers such as: Pyramid from 20 to 70 mm, Butterfly 20/25/30, 35/40/50, Support from 20 to 50 mm, Cone from 20 to 70 mm, Half-cylinder from 30 to 60 mm, Bone 20/25/30/40, 35/40/45/50, and other types by individual order.
Technical specifications
Technical specifications | bricket-80AT |
---|---|
Parameter name: | Meaning: |
Pressing pressure, two-way counter: | 80 tons + 80 tons |
Hydraulic system pressure: nominal / maximum (MPa) | 18 / 22 |
Machine dimensions, weight: | |
Length, width, height (mm) Weight: (kg) | 1800 - 1450 - 2150 1650 |
Calculations: | |
Number of products per cycle: butterfly, pyramid, cylinder | 12 |
Duration of one cycle | 18 seconds |
Productivity, pieces/hour | 2400 |
Electric motor power, (kW) working / maximum | 7 / 15 |
Working hours: | |
Loading the mixture into the chamber | automatic |
Product molding | automatic |
Ejecting the product | automatic |
Advantages of ERMANI presses
Double-sided counter pressing: 80 tons + 80 tons
The pressure per unit of product is not less than 400 kg per cm2.
The number of products is determined depending on the configuration and cost of the equipment.
The height of the product is adjustable: from 10 to 80 mm and higher upon customer request.
Product pressing system. With a certain material composition, it is possible to press the product an unlimited number of times.
The forms are assembled from special wear-resistant steel, which undergoes special heat treatment.
Simple and clear control of the press, which includes: Mode: manual (setup), semi-automatic, automatic.
A reliable, inexpensive to repair, hydraulic station: consisting of high-quality, affordable components that have stood the test of time.
Form heating system. Built-in special heating elements allow the form temperature to be set to 180 degrees. Automatically regulated.
Advantages of concrete spacers for rebar
—
Limitations of Ø reinforcement
Load limitation
Deformation
MAIN IMPORTANT ADVANTAGES
Fire resistance
Correct form
Homogeneous material
Concrete spacers
No +
No +
No +
—
Yes +
Yes +
Yes +
Plastic fasteners
Yes —
Yes —
Yes —
—
No —
No —
No —
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Деформация
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Ограничения Ø арматуры
Variety of forms
Simple — reliable
Hydraulics

Reliable hydraulic components, time-tested, operate without failures for many years.
Easily available on the market in any city in the world. Replacement of components does not require the knowledge of a highly qualified specialist.
Automation

Easy-to-use automation. Time-tested components. Available in any market in the world.
Using a USB cable and the Internet, it is possible to change the program characteristics independently or remotely by our specialists.
Mechanics

The mechanical elements of the press are made of thickened materials with a reserve. To withstand the high pressure provided on the hyperpress.
Simple and reliable mechanics of moving elements. We use only hardened columns, ground moving plates, as well as bars, bushings and other elements are protected from dust and dirt by special cuffs.
Forms

We use special wear-resistant steel that undergoes heat treatment to withstand high wear pressure.
The forms are assembled from special high-strength compounds. Special wear-resistant inserts where wear occurs are easily replaceable, so there is no need to replace the entire form. And use the same form for many years.
Write a message